The IP address 192.168.1.254 is the default Private IP for some home broadband routers and modems.
Routers or regular modems using this IP include modems 2Wire, Aztech, Billion, Motorola, Netopia, SparkLAN, Thomson and Westell for CenturyLink.
It sounds simple, but have you really understood its functions?
If you are having difficulties in setting or changing this IP address for some personal purposes, this article is right here for you!
What is the IP Address 192.168.1.254?
192.168.1.254 is a Private IP address, one of the addresses for private networks. This means that a device in this private network cannot be accessed directly from the internet using a Private IP, but by any other device on the local network.
While the router itself has a Private IP of 192.168.1.254, it assigns any device in the network a different Private IP address. All IP addresses on the network must have a unique address on that network to avoid IP address conflicts. Other Private IP addresses used by the modem and router are 192.168.1.100 and 192.168.1.101.
The address 192.168.1.254 is only used for IPv4 addresses. It is impossible to apply this code to an IPv6 address. We can use this IP address as a default IP of the factory on a load of routers, cables, and wireless data cables.
Similar to the 192.168.0.1 address, the address 192.168.1.254 is used in most networks and small businesses, because Internet service providers (ISPs) usually assign a unique IP address to one device to connect to the Internet.
In case if you need to connect multiple devices to the Internet, we will use NAT (Network Address Translation) ports. According to IANA defined in RFC 1918, IP address 192.168.1.254 belongs to class C.
Why Do We Need this IP Address?
Most often, offices and people being at home are the two main subjects who make use of modems and routers with the IP address like 192.168.1.1.
In some cases, the IP address does not work. And in this situation, you can replace it by the IP address 192.168.1.254. This IP code helps users have access to the router on some new devices.192.168.1.254 permits the users to access the settings of a default IP address.
Ultimately, this will solve the problem of the default Router IP address.
Access the Administration of the Router
The manufacturer places the IP address of the router at the factory, but you can change this address at any time using the router’s administration interface. Enter http://192.168.1.254 (not www.192.168.1.254) into the web browser address bar to access the router’s control panel. This is where you can change the router’s IP address and configure some other options.
If you don’t know the router’s IP address, you can locate it using the command prompt as follows:
- Press Windows-X and the Power Users menu will open.
- Click Command Prompt.
- Input “ipconfig” to display a list of all computer connections.
- Find the default port in the Local Area Connection section. This is the router’s IP address you are using.
- Default username and password
All routers have the default username and password. Username/password combinations are standard for each manufacturer and are always determined by a label stuck to the router’s hardware.
The most common are:
| Router | User name | Password |
|---|---|---|
| Router 2Wire | blank | blank |
| Router Aztech | “admin”, “user” or blank | “admin”, “user”, “password” or leave blank |
| Router Billion | admin | admin |
| Motorola router | “admin” or blank | “password”, “router”, “admin”, “motorola” or leave empty |
| Router Netopia | admin | “1234”, “admin”, “password” or leave blank |
| Router SparkLAN | blank | blank |
| Router Thomson | blank | “admin” or “password” |
| Router Westell | “admin” or blank | “password”, “admin” or leave blank |
After you have access to the router’s administrative control panel, you can configure the router in many ways. Be sure to set your username/password safely. If this is not guaranteed, anyone can access the router’s control panel and change the settings of the control panel without your knowledge.
Routers often allow users to change other settings, including the IP addresses they assign to devices on the network.
How Do We Reset the Router?
When you proceed to change the WiFi password to a password range that is difficult to guess, but you accidentally forget the WiFi password. For these cases, users need to reset the WiFi router.
Or if WiFi has trouble, the connection is not stable; you can also apply a way to reset the WiFi router.
When resetting the router, the previous settings that you set will be deleted and restored to their original state.
The Traditional Way To Reset the Router
You can retune your router or alter the admin password of this router with many more straightforward ways. If you cannot access the router’s settings page or forget the router’s password, follow our guides below.
- You have to turn your router into default settings. To do so, you have to press and hold at the same time the Reset button in around 10 seconds.
- The default username of this router may just be blank.
- Make sure the LED power linked to the router blinks immediately after pressing the Reset button.
- The time to implement this Reset approach is based on the router’s model.
- When you are already satisfied with the Reset method, you have to unplug then replug the power adapter.
What About the “Reset Router from Web” Method?
- First, users need to move to the setup page.
- Then, you choose the Administration tab; the Factory Defaults will appear on the screen.
- In the Factory Defaults part, you press the button “Restore Defaults Factory.”
- After changing the router to its default settings, you must reconfigure the device according to the Internet connection you use.
How to Increase the Coverage for Wifi By Ip Address 192.168.1.254 with an Old Router?
To use Wi-Fi, you only need one router. That means when you upgrade, replace the old router with a new router with a higher speed, the old router will become redundant.
However, do you know if you know how you can turn it into an external Access Point (AP)? Placing this AP at the far corners of the house and connecting it to the new router (via a network cable), you can increase the coverage for Wi-Fi waves in places where only one router cannot reach.
The instructions below will help you create this homemade AP.
Your home Wi-Fi router usually has an embedded AP (or even 2 and three integrated APs – with dual-band or 3-band routers), next to its function as a router. The AP helps broadcast Wi-Fi so that wireless clients such as smartphones and tablets can connect to it.
In this article, we will name the primary router is Router A, and the old router you want to turn into AP is Router B. The goal here is to turn Router B into an external AP for Router A to increase the coverage area of the WIFI.
Note: Some Wi-Fi routers have Access Point mode (check this information in their list of features). If your Router B supports this mode, you just need to turn it on, and it will act as an AP and doesn’t need too much effort to set up.
The instructions below are for routers that do not have the above feature (or yes but you do not know how to activate) and are only suitable for web-based routers – a site from which you can view, manage and Control router features and settings.
Fortunately, most routers on the market have this interface, so you don’t have to worry about it being impossible.
Step 1: Ignore the WAN (internet) Port of Router B
If your router does not have an AP feature, you will need to take note to ignore its WAN port. Using this port will cause the router to automatically act as a regular Wi-Fi router – just because it is the function that people initially designed for it. If you are careful, you should stick a piece of tape to this port to avoid confusion.
Step 2: Determine the IP Range of Router A
This step has two parts to do. First, you need to find what the IP address of Router A is. You connect a computer to Router A via Wi-Fi or a network cable through one of its LAN ports.
If your computer is using Windows system, follow these steps:
- Run the command prompt. With Windows 10 you just need to search with the cmd keyword in the Start menu to show the command prompt. With Windows 8, you just need to type cmd while in Metro Start menu and press Enter.
Simply, run Command Prompt by opening the Run dialog box (Windows + R shortcut), typing cmd and pressing Enter.
- In this window, type “ipconfig” before Enter. You will get the result that the words and numbers are very “messy,” however, finding IP addresses is not too difficult.
Look to the “Default Gateway” line and look to the right. That’s the IP address of the router you are looking for.
After having the router’s IP address, you use it to determine its IP range. The number range you can choose to use will match the numbers in the first three groups, with the fourth group ranging from 1 to 254. You must not select the IP address that Router A is using.
If the router’s IP address is 192.168.1.254, the IP range has to be between 192.168.1.1 and 192.168.1.253.
In this article, let’s assume 192.168.1.1 is the IP address of Router A.
Step 3: Set the IP Address for Router B by Taking an Unused Address into Router A’s IP Range
Connect your computer to Router B via Wi-Fi or via a network cable to determine what the router’s current IP is.
You log into the router’s web interface by opening a browser and entering the IP address into the address bar. Inside the interface, you navigate to the section that allows you to change the default IP address of the router. Depending on the model, this item may be named Network, LAN, or Setup. You turn this IP address to an address in the IP range you specify.
For example, if Router A’s IP is 192.168.1.1, you can change the IP of Router B to 192.168.1.254. You must ensure this IP has not been assigned to any other device. Otherwise, you will have to choose another available IP. After selecting, click Save to save the changes. Router B will now restart, and you have to wait for a few minutes.
Step 4: Turn off Router B’s DHCP Server
You log back into the web interface of Router B by pointing the web browser to the new IP address that you set up manually in step 3 (in the above example, 192.168.1.254) and then navigate to the LAN entry. , Network, or Setup. Here you can disable the DHCP server function and click Save to save the changes.
Now, Router B – when connected to Router A with a network cable – will have the function of a switch (allowing you to use its LAN port to connect devices to the network with cables) and an AP. You can log into the router’s web interface with its IP address (in this case 192.168.1.1 of Router A and 192.168.1.254 of Router B) to make changes to the settings.
To Sum Up,
We have just introduced you to the IP address 192.168.1.254. If there are any questions, readers can leave your comments in the comment section below the article; we will answer your questions as soon as possible.
